Concrete Contractor San Diego CA built for flat,
crack-free slabs
As a Concrete Contractor San Diego CA homeowners call back, we pour driveways, patios, walkways and slabs that stay flat and drain right. Our crews handle forming, rebar, pouring and finishing in-house, so you get one team from first stake to final sealer. Free on-site quotes across the city.
Your Concrete Contractor San Diego CA homeowners keep on speed dial
San Diego Concrete Contractor pours and repairs driveways, patios, walkways, slabs and retaining walls across the city and San Diego County. We started in 2019, and since then we have handled everything from cracked La Jolla driveways to sunken garage floors in Mira Mesa. Our crews form, set rebar, pour and finish every job themselves, so nothing gets handed off to a stranger halfway through.
What sets us apart is how we prep. We compact the base, check slope with a laser level, and add expansion joint material at every control line so slabs move instead of crack. If you need a concrete company near me that answers the phone and shows up when it says it will, we do both. We pull permits, meet California Contractor License (CSLB) requirements, and follow ACI Certification standards on every pour.
Concrete services San Diego CA crews handle start to finish
Everything we do starts with the same question: what is this slab going to carry? A driveway in Clairemont takes different prep than a pool deck in Carmel Valley, and a garage floor takes different finishing than a stamped walkway. We match mix design, thickness and finish to the job, then pour it with our own crew. If you have been searching for a concrete company San Diego 24/7 emergency crews, call and we will tell you straight what your project needs.
Concrete Driveway Installation
We pour driveways 4 to 6 inches thick over compacted base and rebar, sized for San Diego soil and summer heat. Broom finish gives you grip on the slope, and control joints go in before the concrete sets so cracks land where you cannot see them.
Concrete Patio Installation
Backyard patios poured level and sloped away from the house, usually 4 inches thick with wire mesh. We finish with broom, salt or stamped texture depending on how you use the space, and seal it so spilled barbecue grease wipes up instead of staining.
Concrete Walkway & Sidewalk Installation
Walkways and sidewalks formed to city right-of-way specs, 4 inches thick with clean edges and even joints. We set the grade so rain runs to the street, not your foundation, and finish with a light broom that stays grippy when it is wet.
Stamped Concrete
Stamped concrete pressed with mats while the slab is still workable, then colored and sealed. We can match flagstone, brick or slate patterns for patios and pool decks. Sealer gets reapplied every 2 to 3 years to keep color from fading in the sun.
Concrete Slab Installation
Slabs for garages, sheds, additions and equipment pads, poured 4 to 6 inches thick with rebar or wire mesh. We check flatness with a laser level and leave a curing compound on top so the slab gains strength instead of drying out too fast.
Concrete Foundation Construction
Foundations formed and poured to IBC and ASTM Standards, with rebar tied to Simpson Strong-Tie hardware at anchor points. We set forms, verify elevation, pour, and strip clean, so your framer can start on schedule instead of waiting on concrete.
Concrete Retaining Walls
Retaining walls poured or block-built to hold back slope on hillside lots in La Jolla, Point Loma and Rancho Bernardo. We size footing and drainage behind the wall so water pressure does not push it over after the first heavy winter rain.
Concrete Repair & Restoration
We repair spalling, cracking and joint failure on existing slabs instead of tearing everything out. Loose material gets cut back with a concrete saw, the patch is bonded with Sika or Euclid Chemical products, and the surface is finished to match what is already there.
Concrete Resurfacing & Overlay
A thin overlay goes over sound but ugly concrete at a fraction of replacement cost. We grind or shot-blast the surface first so the new layer actually bonds, then finish and seal it. Best for patios and walkways that are worn but still structurally solid.
Concrete Removal & Replacement
We break out old slabs with a concrete saw and jackhammer, haul the rubble, and pour new concrete in the same footprint. Most residential driveways and patios take 2 to 4 days from demo to cure. We protect landscaping and keep the work zone clean.
Concrete Sealing
Sealer keeps water, salt and UV off your slab and slows efflorescence and staining. We clean the surface first, let it dry, then roll or spray a penetrating or film-forming sealer. Most San Diego slabs need resealing every 2 to 3 years.
Concrete Staining
Acid and water-based stains soak into cured concrete for color that will not peel like paint. We test a sample patch first so you see the actual tone on your slab, then seal it. Popular for patios, interior floors and pool decks.
Polished Concrete
Polished concrete floors ground through progressively finer grits until the surface shines, then densified and sealed. No wax, no coating to peel. We use it in garages, shops and modern interiors where dust and tire marks are a problem.
Concrete Countertops
Countertops cast from Portland cement, aggregate and admixtures, then polished and sealed for kitchen and bath use. We build forms to your dimensions, cast, cure and finish. Heat-resistant and one-of-a-kind, with color matched to your cabinets.
Concrete Steps & Stairs
Exterior and interior steps poured to consistent rise and run, with a broom or stamped finish for grip. We form each step, tie it to the slab or footing, and check tread depth so nobody catches a toe on the way up.
Concrete Pool Decks
Pool decks poured and finished with a cool, slip-resistant texture around the water. We slope away from the pool shell and coping so splash water drains instead of puddling. Salt damage and freeze-thaw damage are not issues here, but sun and chlorine are.
Concrete Garage Floors
Garage slabs poured flat and dense, then sealed against oil, brake fluid and road salt tracked in off the street. We pour 4 to 6 inches with rebar and control joints. A sealed floor wipes clean instead of turning into a permanent stain.
Concrete Driveway Resurfacing
When a driveway is cracked but the base is still good, resurfacing saves the tear-out cost. We prep, patch and pour a bonded overlay, then cut new control joints. Expect 2 to 3 days of work and a driveway that looks new again.
Concrete Driveway Repair
We fix cracked, spalled and settled driveways with targeted repairs instead of full replacement. Cracks get routed and filled, spalled areas get patched, and joint failure gets re-cut and re-sealed. Most repairs are done in a single day.
Concrete Patio Repair
Uneven, cracked or crumbling patios get leveled, patched or partially replaced depending on what failed. We check drainage first, because a patio that puddles will keep failing no matter how good the patch looks. Then we match the finish.
Concrete Leveling & Mudjacking
Sunken slabs get lifted back to grade by pumping material underneath through small holes, then patching the holes flush. Cheaper and faster than replacement, and it works well on driveways, walkways and garage aprons that settled over time.
Concrete Crack Repair
We route cracks open, clean them out, and fill with flexible or rigid repair material depending on whether the slab is still moving. Cracks under a quarter inch get sealed; wider ones get epoxy or polyurethane injection. Then we match the surface.
Concrete Expansion Joint Installation
Expansion joint material goes in where slabs meet walls, columns or other slabs, so movement has somewhere to go. We cut clean lines, set the joint material, and seal the edges. Skipping this step is why so many slabs crack at the corners.
Concrete Pumping Services
When a pour is too far from the street for a chute, we bring in a concrete pump and place the mix exactly where it needs to go. This keeps you from wheelbarrowing 20 yards across a finished yard. Standard for backyard and hillside pours.
Concrete Formwork & Framing
Forms set straight, braced hard and oiled with form release agent so they strip clean and leave sharp edges. We build to the actual dimensions of your project, not close enough. Good formwork is why the finished slab looks right from every angle.
Rebar & Reinforcement Installation
Rebar and wire mesh placed on chairs at the right height in the slab, tied at every intersection, and cut with a rebar cutter for clean ends. Reinforcement is what keeps concrete from pulling apart under load. We never skip it to save a buck.
Decorative Concrete Finishes
Decorative finishes include stamping, staining, exposed aggregate and saw-cut patterns, all done while the concrete is workable or shortly after cure. We walk you through samples first so you know exactly what your slab will look like before we pour.
Exposed Aggregate Concrete
Exposed aggregate shows the actual stone in the mix by washing the top layer of cement away before it fully sets. The result is a textured, non-slip surface that hides dirt well. Popular for driveways and pool decks around San Diego.
Broom Finish Concrete
A broom dragged across wet concrete leaves fine lines that give grip without being rough on bare feet. It is the standard finish for driveways, sidewalks and patios, and it holds up to years of foot traffic and sun without looking worn.
Colored Concrete
Color goes into the mix or gets applied as a stain or hardener on top, so the slab is colored all the way through instead of painted. We match tones to your house, hardscape and roof. Sealer locks the color in against UV fade.
Why we are the best Concrete Contractor in San Diego
Prep work that prevents cracks
We compact the base, set rebar on chairs at the correct height, and cut control joints before the concrete sets. That combination is what stops the random cracking you see on cheap slabs. It costs us more time and it is worth every minute.
Licensed, insured, code-compliant
We hold a California Contractor License (CSLB), carry insurance, and pour to IBC and ASTM Standards. Permits get pulled when the job needs them. If a city inspector is going to look at the work, we want it to pass the first time.
One crew from form to finish
The same team that sets your forms also places the rebar, pours the mix and finishes the surface. Nothing gets subbed out to a crew you have never met. You get one point of contact and one number to call if anything comes up.
Fast response, 24/7 emergency line
Slab cracked and water is running toward your foundation? Call any hour. We answer 24/7, and for urgent repairs we can usually get eyes on the problem the same day. For scheduled work, most quotes go out within 24 hours of the site visit.
Get a straight quote on your slab today
Anyone can rent a mixer and pour a slab. Doing it so the slab is still flat and crack-free five years later takes prep, the right mix and a crew that finishes before the concrete sets. That is the part we take seriously, and it is why homeowners from Ocean Beach to Escondido keep calling us back.
Call for a quoteHow our concrete work gets done
On-site walkthrough
We come out, measure the area, check the base and drainage, and talk through what you want. You get a written quote with the thickness, reinforcement and finish spelled out. No vague numbers.
Prep and forming
We demo and haul old concrete if needed, compact the base, set forms and place rebar or wire mesh. Forms get oiled with form release agent so they strip clean. This stage takes the longest and matters the most.
Pour and finish
Concrete arrives by truck or concrete pump, gets spread with a screed, consolidated with a vibrator, then floated and finished. We cut control joints and apply curing compound while the slab is still green. Finish is broom, stamped or exposed aggregate, your call.
Cure, seal and walkthrough
Concrete cures over 7 to 28 days, and we seal it once it is dry enough. We walk the finished job with you, point out the joints and drainage, and tell you when it is safe to park on or set furniture. Then we get out of your way.
Concrete problems San Diego homeowners call us about
Driveway cracked into random spiderweb lines
Random cracking usually means the slab had no control joints or the base was not compacted. We cut and fill the existing cracks, then either resurface the driveway or replace the failed sections with proper joints and reinforcement so it stops spreading.
Patio slab sinking and puddling after rain
Settlement happens when the soil under a slab washes out or compresses. We lift the slab back to grade with mudjacking, then fix the drainage that caused the problem. Most sunken patios get leveled in a single day without a tear-out.
Surface spalling and flaking off in sheets
Spalling is the top layer of concrete coming apart, often from too much water in the mix or salt exposure. We chip off the loose material, prep the surface, and apply a bonded overlay or patch. Sealing afterward keeps it from happening again.
White powder blooming on the slab surface
That white haze is efflorescence, mineral salts pushed to the surface by moisture. We clean it off, find where the water is coming from, and seal the slab so moisture stays out. If it keeps coming back, there is a drainage issue to fix first.
Uneven, trip-hazard walkway slabs
Lifted or dropped walkway sections are a real trip risk, especially for kids and older neighbors. We level the slabs, grind down high edges, or replace individual sections so the whole path is even again. Usually done in a day or two.
Joint failure and crumbling edges
When expansion joints fail, slabs push against each other and the edges break down. We re-cut the joints, clean them out, install fresh expansion joint material, and seal the edges. This stops the movement that was chewing up the concrete.
What San Diego customers say
"Our driveway in Clairemont had cracks running everywhere and one corner had sunk about two inches. They lifted the sunken section, patched the cracks and resurfaced the whole thing. Two days of work and it looks brand new. They even swept the street before they left."
"We had them pour a stamped patio in Carmel Valley and the color match to our flagstone was spot on. They showed us samples first, which I appreciated. Crew was on time both days and cleaned up everything. Sealer still looks good a year later."
"Called them on a Saturday because a slab near our garage had cracked and water was pooling against the house. They answered, came out that afternoon, and had it patched and sealed by Monday. Fair price and no runaround. Would use them again."
"We needed a new garage slab for a shop build in Mira Mesa. They handled the forms, rebar and pour, and the floor is dead flat. My framer said it was one of the better slabs he has worked on. Finished on the day they said they would."
"Our pool deck in La Jolla had spalling all over from the salt air. They chipped it back, prepped it and put down an overlay with a cool texture. It is way easier on bare feet now and it drains properly. No puddles after the last rain."
"Small job, just a walkway and some steps in Hillcrest, and they treated it like it mattered. Gave me a written quote the same day, showed up when they said, and the steps are all even. Nice to deal with a concrete company that actually answers the phone."
Concrete company serving San Diego County neighborhoods
Concrete Contractor Coverage Across San Diego & San Diego County
Routine and same-week appointments for residents and businesses across San Diego County, including the ZIP codes below.
Concrete Contractor San Diego CA questions answered
These are the questions we get asked most, with straight answers. If yours is not here, call us and we will give you a real number over the phone.
How much does a Concrete Contractor cost in San Diego?
Typical 2026 pricing in San Diego runs $8 to $18 per square foot for new concrete, depending on thickness, reinforcement and finish. A basic broom-finish driveway usually lands around $10 to $14 per square foot, while stamped or exposed aggregate work runs higher. Small repairs often start around $400. We give you a written quote after seeing the site.
Who is the best concrete company in San Diego CA?
The best concrete company in San Diego California is the one that preps the base properly, uses the right reinforcement, and finishes before the mix sets. Ask any contractor how they compact the base and where they place rebar. We answer those questions straight, hold a California Contractor License (CSLB), and pour to ACI Certification and ASTM Standards on every job.
Are there 24/7 concrete contractors in San Diego?
Yes. We run a 24/7 emergency line for urgent concrete problems like a cracked slab leaking toward your foundation or a failed retaining wall. For non-urgent work, we schedule site visits within a day or two and most quotes go out within 24 hours. Call any time and a real person picks up.
How to choose a concrete contractor in San Diego?
Check three things: a valid California Contractor License (CSLB), active insurance, and whether they pour with their own crew or sub it out. Then ask about base prep, rebar placement and joint spacing. A contractor who can explain those clearly is usually the one who does the work right. Get everything in a written quote before you commit.
Do I need a licensed concrete contractor in San Diego California?
Yes, for any structural work like foundations, retaining walls or slabs tied to a building, California requires a licensed contractor. We hold a California Contractor License (CSLB) and pull permits when the job needs them. For small cosmetic repairs, licensing rules are looser, but hiring licensed is still the safer call.
Ready for a Concrete Contractor San Diego CA you can trust?
Call San Diego Concrete Contractor at +1 619-231-1616 for a free on-site quote. We answer 24/7, schedule fast, and pour concrete that stays flat and crack-free for years. Serving the city and San Diego County since 2019.
Call nowContact our concrete crew
info@sandiegoconcretecontractor.com
Monday - Friday: 7:00 AM - 6:00 PM
Saturday: 8:00 AM - 4:00 PM, Sunday: Emergency calls only